Glock 17 ejector question

Discussion in 'Glock Forum' started by Joshe1190, Jun 25, 2018.

  1. Joshe1190

    Joshe1190 New Member

    4
    1
    Hello, So I am new to the Glock world and recently did a polymer80 G17 build. However I am having a problem. I used a Lone Wolf Distributors Frame completion kit, Part # LWDSPECTREFULLS on Brownells website, and I am not sure I have the right ejector installed because every time I fire the weapon, the casing comes straight back and normally hits my left arm or hat. This kit came with 2 ejectors, one for the 9mm and one for the 40 S&W. Could someone please help me figure out which one I need to use in my gun. If you go to brownells page, the ejector I am currently using is the bottom one, which comes to more of a point. I included some photos to help people understand what I am talking about. Glock 17 ejector 1.JPG Glock 17 ejector 2.JPG
     
  2. Joshe1190

    Joshe1190 New Member

    4
    1
    Any help would be greatly appreciated!
     

  3. Dark Knight

    Dark Knight Administrator Staff Member Admin Moderator Lifetime Supporting Member

    130,056
    16,555
    I'm sure bob will be along in the morning to fix it for you .
     
    cazbass, rbbeers and Panzergraf like this.
  4. rbbeers

    rbbeers Well-Known Member Lifetime Supporting Member

    3,450
    4,132
    Hi, Joshe!

    Welcome to the forum!

    To glockoid's point...

    The LWD ejectors should look similar to the Glock parts pictured below.

    Ejectors 1.jpg

    Ejectors 2.jpg

    Please let us know if you have further questions.

    Best regards,

    Bob
     
    Last edited: Jun 26, 2018
  5. Southlake

    Southlake Island Life Staff Member Moderator Lifetime Supporting Member

    56,806
    22,519
    Welcome to the Glock Forum.
     
  6. Southlake

    Southlake Island Life Staff Member Moderator Lifetime Supporting Member

    56,806
    22,519
    Thanks Bob! :D
     
    rbbeers likes this.
  7. Joshe1190

    Joshe1190 New Member

    4
    1
    So according to the pics y’all have shown me, I need to switch the ejectors out to the right one.. I’m just tired of eating brass after every shot lol
     
    cazbass likes this.
  8. rbbeers

    rbbeers Well-Known Member Lifetime Supporting Member

    3,450
    4,132
    Hi, Joshe!

    The pictures below are excerpted from your pictures in post #1.

    My guess is that the ejector below is LWD's 9mm ejector... of the two ejectors, it appears to match Glock's 30274 ejector the best.

    Glock 17 ejector 1.JPG

    I'm assuming that the ejector below is LWD's 40 cal ejector.

    Glock 17 ejector 2.JPG

    However, as you may note, it doesn't really match Glock's 1882 ejector very well and may be an attempted copy of Glock's 40 cal 28926 ejector (shown below).

    Ejectors 3.jpg

    Hope this helps.

    Again, if you have further questions, please ask.

    Best regards,

    Bob
     
    Last edited: Jun 26, 2018
    L-2 likes this.
  9. rbbeers

    rbbeers Well-Known Member Lifetime Supporting Member

    3,450
    4,132
    Hi, Joshe!

    Look at the ejectors from the top (shown below)...

    Ejectors 4.jpg

    The 9mm ejector is (should be?) bent 'in' toward the center of the pistol (red arrow above).

    Best regards,

    Bob
     
    cazbass and Southlake like this.
  10. rbbeers

    rbbeers Well-Known Member Lifetime Supporting Member

    3,450
    4,132
    Hi, Joshe!

    Question...

    What extractor, spring loaded bearing, and extractor depressor plunger & spring assembly are you using?

    Best regards,

    Bob
     
    Last edited: Jun 26, 2018
  11. rbbeers

    rbbeers Well-Known Member Lifetime Supporting Member

    3,450
    4,132
    Here's a slightly better picture...

    Ejectors 5.jpg

    And, here's the 40 cal 28926...

    Ejectors 6.jpg
     
    Last edited: Jun 26, 2018
    Southlake likes this.
  12. Joshe1190

    Joshe1190 New Member

    4
    1
  13. rbbeers

    rbbeers Well-Known Member Lifetime Supporting Member

    3,450
    4,132
    Hi, Joshe!

    If you post 'top view' pictures (similar to post #12), we can help you identify the 9mm ejector.

    This kit?

    https://www.brownells.com/handgun-p...letion-kit-for-glock-17-gen-3-prod108558.aspx

    Also, is the extractor in the kit Glock part number 1895 (as shown below)?

    9mm extractor.jpg

    Best regards,

    Bob
     
    Last edited: Jun 27, 2018
    Southlake likes this.
  14. Southlake

    Southlake Island Life Staff Member Moderator Lifetime Supporting Member

    56,806
    22,519
    Thanks Bob, do you sleep?
     
    rbbeers likes this.
  15. rbbeers

    rbbeers Well-Known Member Lifetime Supporting Member

    3,450
    4,132
    Hi, TJ!

    You're very welcome!

    LOL!

    A few hours a night... sometimes a bit more. :D

    Best regards,

    Bob
     
    Last edited: Jun 27, 2018
    Southlake likes this.
  16. Southlake

    Southlake Island Life Staff Member Moderator Lifetime Supporting Member

    56,806
    22,519
    Bob,

    It's Jim these days. I had to add trainer because Jim was taken.
     
    rbbeers likes this.
  17. rbbeers

    rbbeers Well-Known Member Lifetime Supporting Member

    3,450
    4,132
    Hi, Jim!

    "Jim" it is!

    Best regards,

    Bob
     
    Southlake likes this.