Glock Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 27 Results
  1. General Firearm Forum
    Hi, I’m pretty sure I know the answer to this but I have just a quick question about DLC coatings. A few mouths back I had my slide and barrel coated in DLC. When I receive the parts back I briefly looked the coating over and because of Thanksgiving and Christmas I stored it in my safe. I just...
  2. Glock Forum
    I am wanting to make my G23 into a G23XL. So basically making it a G35 on the top half. Which of these manufacturers should i go with ? If you know any other companies that do custom fabrication that might be better than these 2, please recommend. Bar sto said they can get it done for me and...
  3. Gunsmithing
    Hey everyone! I recently purchased my first Glock(s) - A Glock 36 and a Glock 19 gen 4.. I purchased an aftermarket barrel for both guns. For the G19 I got an agency arms (which fit perfectly) and for the G36 I bought a factory style barrel in SS. The new barrel for the Glock 36 is causing the...
  4. Glock Forum
    Hi there, I have a Glock 17 Gen 3 That i replaced the Factory/OEM/Stock Barrel with a Direct Fit Drop in Stormlake Stainless Steel Barrel, I replaced the Barrel Probably about 2011. The Reason i Replaced the Barrel is because i was shooting Cast Lead Bullets that i used to get from a buddy who...
  5. Sold/Expired
    For sale is my BarSto #363909, 9mm G17 Semi Fit Barrel. BARREL HAS BEEN SOLD.
  6. Sold/Expired
    I have a brand new True Precision G19 Threaded Barrel for Sale that is in Rose Gold. There is nothing wrong with the barrel, I have just decided to go in a different direction with my G19 build. Pictures can be found here: https://imgur.com/a/cofGQdl I gave $230 for the barrel last month...
  7. Sold/Expired
    Brand new G32 Factory .357 sig barrel, never been fired, came out of a gen 3 slide. $110 shipped.
  8. Sold/Expired
    See title. Bought last week, put into firearm, Decided I love the barrel, but not in that pistol. My loss is your gain. 260 shipped. Will trade for same barrel or equal quality in black.
  9. Glock Forum
    Hi all, I have a recently built p80 g19, and am encountering some issues, wondering if anyone has dealt with this. In order to rack my slide properly and have it go fully into battery I have to push down on the chamber and "seat" the barrel. It will usually get stuck, at which point I have to...
  10. Sold/Expired
    LoneWolf 3.78", 9x25 Dillon barrel for a Glock 29. Less than 50 rounds through it, and never anything rapid. Also have twenty rounds of 124 grain XTP & twenty rounds of 124gr Bonded Nosler from Underwood to go with it. Id like to trade it for a 4.5"-4.6" 10mm barrel to fit my 29, but I'm open...
  11. Sold/Expired
    Hi im looking to buy a complete upper for a Glock 19 gen 4 9mm. Pm on what you have to offer. Best regards Hopii1
  12. Glock Forum
    So i have a Glock 17 (Gen 3) its pretty new, only shot about 220 rounds through it, and i was shooting some cheap steel cased ammo yesterday, and i had a bad round and most of the powder didn't go off so the bullet got stuck in the barrel so i got home and got a little rod and a hammer and...
  13. Sold/Expired
    I want to sell an almost new Alpha Wolf Glock 19 1/2x28 threaded barrel for $110 (MSRP is $160). It has never been fired through, only put into a Glock 19 and the slide worked a few times. I also have the matching compensator for $25 (MSRP is $50) The compensator shows very slight wear from...
  14. General Firearm Forum
    A month or few back I purchased a RIA TAC Ultra FS HC 40SW. Based on my natural curiosity I was wondering if I would be able to swap out the barrel and recoil spring and have a 10mm? After much interwebs hunting, I found that I can do this swap all I would need is the barrel and a #20 recoil...
  15. Glock Forum
    Just got my 30 SF and took it to the range fired 50 rounds and noticed heat marks on the tip of muzzle (barrel). Was wondering if that is normal or do I need get it checked out.
  16. Glock Forum
    Is it worth searching for a barrel with reversed rifling for a left handed shooter? If so, any suggestions? If not, any suggestions on an after market barrel? For a glock19 gen 4, carry and range.
  17. Glock Forum
    I am looking into changing the barrel on my G22 Gen 3 from a 40 to 9mm from Lone Wolf. What mags can I use in the pistol for 9mm rounds..
  18. Glock Forum
    OK, I just got a used Glock 32c and was wondering if its possible to put a G20 barrel in it.; If so, I imagine I would need G20 magazines as well? I am already looking into G23/G22 barrels for it as an alternative. The .357sig ammo is a bit more accessible now and I have really been enamored...
  19. Sold/Expired
    For ale this Glock G22 Lone Wolf conversion barrel .40 to 9mm Threaded 1/2 x 28. Tread protector is included. Mint, maybe 50 rounds down the pipe. Price: $SOLD OBO. Email: fmjarms@yahoo.com
  20. Sold/Expired
    For sale or trade: Used Glock 22 OEM barrel (.40S&W) in great condition. Approx. value $125. What do you have? In Abilene, TX. coolcomputerguy at g mail dot com. Always looking for gear for my 33,23 and 30s, M&P15-22 and Ruger 10/22.
1-20 of 27 Results
Top